Yahoo Web Search

Search results

1. Images

   • 
   • 
   • 
   • 
   • 
   • 

   View all

2. mobilehomeliving.org › wp-content › uploadsElectric Water Heaters - Mobile Home Living

   mobilehomeliving.org › wp-content › uploads

   Model: GE Series. The purpose of this manual is twofold: one, to provide the installer with the basic directions and recommendations for the proper installation and adjustment of the water heater; and two, for the owner– operator, to explain the features, operation, safety precautions, maintenance and trouble shooting of the water heater.

   • File Size: 402KB

   • Page Count: 20

3. www.mobilehomerepair.com › phpbb › viewtopicIntertherm Model FEH-012HA - mobilehomerepair.com

   www.mobilehomerepair.com › phpbb › viewtopic

   • Cached

   A few years back our mobile home electric furnace started blowing cold air. We checked it and seen that it had burnt a wire inside. We replaced that wire with higher grade wire, and it burnt that wire also. Element is fine, blower is fine, fuses replaced, but it keeps burning the wire and causes the air to blow cold.

4. www.broan-nutone.com › getmedia › 214ddc09-0b7b-43f8READ AND SAVE THESE INSTRUCTIONS - Broan-NuTone

   www.broan-nutone.com › getmedia › 214ddc09-0b7b-43f8

   Your heater is equipped with a manual-reset ther-mal overload protector. If heater fails to operate when thermostat is turned to its highest setting: 1)Turn off power at service entrance. 2)Remove knob and grille. 3)Press button marked “RESET”. This type of device is particularly useful (compared to automatic reset devices) because it ...

5. rexel-cdn.com › Products › KingElectricalIMPORTANT INSTRUCTIONS

   rexel-cdn.com › Products › KingElectrical

   power to the heater o˚ for 10 minutes to reset the SLP thermal protector. If the SLP thermal protector shuts the heater o˚ again, immediately turn the heater OFF at the circuit breaker and inspect the heater for possible fan motor failure or dirt and lint on the heating ele-ment. Repeat the starting procedure. DO NOT TAMPER

6. www.mobilehomerepair.com › restring-furnaceHow to Restring a Furnace Heating Element - Mobile Home Repair

   www.mobilehomerepair.com › restring-furnace

   • Cached

   Step 1: Turn off electrical power to unit. You may have more than one circuit, so check for other breakers or fuses. Then disconnect the electrical connections to the unit after testing with a meter to ensure that indeed all the power has been cut. Step 2: Take careful notes on how the heating element is wired. Taking pictures is also a good idea.

   • 
   • 
   • 
   • 

7. www.manualslib.com › manual › 2322512BROAN BHFLED80 INSTRUCTIONS MANUAL Pdf Download | ManualsLib

   www.manualslib.com › manual › 2322512

   • Cached

   READ AND SAVE THESE INSTRUCTIONS IMPORTANT INSTRUCTIONS FIG. 1 READ ALL INSTRUCTIONS BEFORE INSTALLING OR USING THIS HEATER. Page 2 MODELS BHFLED80 • BHF80 Page 2 FIG. 6 INSTALLATION BLUE FIG. 11 WARNING: To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater. GROUND ...

8. mobilehomeliving.org › wp-content › uploadsElectric Water Heaters - Mobile Home Living

   mobilehomeliving.org › wp-content › uploads

   The temperature of the water in the heater is regulated by the adjustable surface mounted thermostat(s) located behind the jacket access panel(s). Dual element heaters have two thermostats. To comply with safety regulations the thermostat(s) were set at 120°F before the water heater was shipped from the factory. The illustration at the left