Search results
Oct 30, 2018 · Join us as we install a brand new door knob. This is a fast, easy, & friendly DIY project!
- 7 min
- 219.3K
- DIY with Michael Borders
- Method
- Tips
Remove the old door knob, latch, and strike plate. If you have not already removed the old door knob and latch, take it out before you begin installing the new one. Depending on the door, you may also need to remove the strike plate—to take it out, remove the top and bottom screws with a screwdriver and lift it carefully out of the door.[1] X Research source The strike plate is a ...Install a latch plate on top of the latch. Depending on the door mortise (the hole that the latch sits in), the latch plate may be round or rectangular. If your latch came with a rectangular plate and you need a round one (or vice versa), take measurements of your latch plate. Purchase a latch plate that fits your door mortise and, after prying off the old plate, place the new latch plate on ...Slide the latch inside the edge of the door. Insert the latch through the door hole so the flat (beveled) side of the latch is facing the door jamb. If the beveled side does not face the jamb, you may have difficulty closing the door.[3] X Research sourceUse a wooden block and a hammer to tap the latch into place. If you cannot fully slide the latch in, place a thick, rectangular block of wood over the end of the latch. Tap the latch into the hole with a hammer until the latch's back reaches the end of the hole.[4] X Research sourceSecure the latch into the door with 2 screws. Most latches are secured to the door with a screw on the top and bottom. Adhere the latch to the door with as many screws as required by its design. Do not buy any additional screws. If your latch needs screws, they will likely come as a set.Follow any installation guides that come with the door knob for additional instructions. Thanks Helpful 2 Not Helpful 2Measure your door before purchasing a door knob to make sure you install the right size. Thanks Helpful 3 Not Helpful 4- 306.6K
- Measure up. Lay a dust sheet under the door you are working on to collect sawdust and wedge the door firmly open, so it won’t move around while you work.
- Drill a hole for the spindle. Using the pilot hole you marked for the spindle, drill through the door. The standard size for spindles is 8mm square, so a flat wood drill bit around 10mm is ideal, but do consult the door knob specification for specific measurements.
- Drill a hole for the latch. Using a 20-25mm drill bit (again, check the latch manufacturer’s specifications), drill into the end of the door for the latch.
- Chisel out the faceplate. Push the latch cylinder into the hole you just drilled, and check it aligns with the spindle holes (remember it will go in a couple millimetres more once the faceplate is chiselled out).
- Remove the Old Door Knob, Latch, and Strike Plate. The exact steps to remove your old door knob will vary depending on its type, but the process is similar for most varieties.
- Set Up Your New Latch/Latch Plate. Now that you have the old door knob and hardware out, it’s time to get the replacement ready. New door knobs should come with all new hardware, but if not, you can reuse hardware if it’s the same type of door knob.
- Install the Latch and Latch Plate. Once you set up the two pieces, installing them is a fairly straightforward process. Push the back of the latch through the opening on the side of the door.
- Install the First Door Knob. When you look in the area where the door knob goes, you should be able to see an opening on the latch where you need to line up the mechanism on the knob.
Sep 19, 2023 · Press on the hole to disengage the knob. 3. Pull the interior knob away from the door. Hold the door with one hand while you pull the knob away from the door. Continue to pull the knob until it detaches from the door. You may have to wiggle it back and forth if it’s stuck on the doorknob stem. [1] 4.
- 651.8K
Jul 25, 2024 · How To Install A Door Knob? 7 Steps. If you are a newbie and don't know much about the installation of door furniture like the door knobs, the following are the steps that you should follow to install them with ease: Step 01: Remove The Old Door Knob. If you are replacing the old door knob with a new one, you would first need to remove it.
People also ask
How do you install a new door knob?
How do I choose a new doorknob?
How do you secure a doorknob?
Find this door knob here on Amazon:https://amzn.to/436TXOWStep by Step Door Knob Install for Beginners #diy #doorknob #homeimprovement This is a step by step...
- 6 min
- 26.4K
- Rosco Reviews
