Search results
- Attach the rain gauge armature to the metal tube using the attached screws and nuts. The two halves piece together with the metal tube in between. Once you have it located where the rain gauge will be clear of the anemometer and wind vane, tighten it into place. Once again, the rain gauge has notches to ensure it mounts snugly on the armature.
learn.sparkfun.com/tutorials/weather-meter-hookup-guide/all
People also ask
How do you attach a rain gauge to a wind vane?
How do you use a wind vane?
How do I attach a rain gauge?
How do you put a wind vane in a bottle?
How do you connect an anemometer to a wind vane?
Can you use a rain gauge outside?
May 27, 2020 · Make your own weather station. ...more.
- 13 min
- 560
- Always KristynJW
- Draw an arrow 25 cm long on the card and cut it out.
- Make another arrow by drawing around the first arrow and cutting it out.
- Place the pen top between the arrows, in the centre facing down, and glue together.
- Push four matchsticks into the long edge of the cork at right angles to each other.
Jul 13, 2020 · Where does the wind blow from? How much did it rain? And how warm is it today? With a self-made garden weather station — which you create when you build a weathervane with a thermometer and rain gauge attached — you can easily answer these questions yourself.
- Temperature Sensor. To measure temperature and humidity I will use the DHT22 sensor. I soldered the sensor onto a perfboard, with a connector and a pull-up resistor between 3,3v and the signal pin.
- Wind Vane. Then we have the wind vane, which detects which direction the wind is coming from. Also for this one I had to make some parts with the 3D printer.
- Anemometro. Now comes the anemometer. I already talked about this in a video last year, which you can find here. I also made the anemometer with the 3D printer, and below you can find the STL files.
- Rain Gauge. Lastly, there is the rain gauge. I showed this in a previous Instructable, so you can find all the details there, including the 3D printable files.
- Armature
- Anemometer
- Wind Vane
- Rain Gauge
- Wire Management
- Mount The Meter
To begin, find the two metal tubes, and slide them together. Next, add the armature to the top of the tube set. Make sure to line up the nub on the armature with the notch in the tube. Use one of the included screws and nuts to lock it in place.
Next, we will mount the anemometer on one side of the armature. The anemometer has a nub on it that matches notches in the armature. This will help secure the anemometer once attached and only allows the sensor to be mounted in one direction. Slide the anemometer onto the armature until it locks in place. Use an included screw and nut to lock the s...
To attach the wind vane, you will follow the same procedure as installing the anemometer. Line up the sensor and the armature, and push the wind vane into place. Once again, use a screw and nut to secure the sensor in place.
To attach the rain gauge, we also need a secondary armature. This is used to keep the rain gauge away from the other sensors to ensure it can get an accurate measurement. If the rain gauge is mounted underneath the wind vane or the anemometer, they can block rainfall into the gauge or offset the readings due to runoff. Attach the rain gauge armatur...
If you've gotten this far, congratulations! Now it's on to the easy part -- cable management. Luckily, this isn't nearly as difficult as some wiring projects. Unravel the wires from the anemometer and the wind vane. On the bottom side of the armature, you will see clips to hold these wires in place. Slide the wire from each sensor into those. Once ...
Now that you've got your meter assembled, you need to place it somewhere with weather! You can use the included gear clamps to help mount and secure your meter. To show a demonstration of how to use the gear clamp, we slid a gear clamp around our meter and a piece of PVC pipe. Then tighten the gear clamp using a flat head screw driver. Keep in mind...
Choose an open area, perhaps near your rain gauge, to place your wind vane. Use a compass to point the N label on the bottle towards North. The arrow always shows the direction the wind is blowing from.
Aug 7, 2024 · Weather instruments like a barometer, an anemometer, a sling psychrometer, a wind vane, and a rain gauge all help the National Weather Service to gather important information about the weather. [1] You can create five weather instruments at home using home supplies and detailed instructions. Part 1.
- 182K
- bestproductsreviews.co.uk/Rain-Gauges
AdRain Gauge - Best Rain Gauge - See What Our Experts Recommend
bestproductsreviews.co.uk has been visited by 10K+ users in the past month
Rain Gauge with Durable Design, Weatherproof Materials. Rain Gauge with Accurate Measurement, Easy Installation
