Search results
- For instuctions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. Keep door open. Press the Program button once. The Checkmark will fl ash fi ve times and you will hear fi ve beeps.
images.kwikset.com/is/content/Kwikset/Support/Tech Docs/915-programming-troubleshooting.pdfProgramming and Troubleshooting Guide Mastercode 2 ... - Kwikset
People also ask
How do I add a user code if the mastercode is disabled?
Why do I need a mastercode?
Can a mastercode unlock a door?
How do I re-enter a mastercode?
What is a mastercode / 0 / 62812 / 01?
How do I know if my mastercode program is successful?
For instructions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. 1. Keep door open. Press the Program button once. The Checkmark will flash five times and you will hear five beeps. 2. Press Checkmark symbol once. 3. Enter Mastercode.
The procedure for adding user codes is different when the Mastercode is enabled. For instuctions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with
- 1MB
- 15
Adding User Codes with the Mastercode Enabled. The procedure for adding user codes is different when the Mastercode is enabled. For instuctions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. Keep door open.
- C Adding User Codes with the Mastercode Enabled
- Keypad error test
- No user codes are programmed.
- The lock is in sleep mode.
- Troubleshooting: Battery
- Keypad error.
- What type of batteries do you recommend?
- I am planning to be away for several months. Will my lock operate when I get back?
The procedure for adding user codes is different when the Mastercode is enabled. For instuctions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. Keep door open. Press the Program button once. The keypad will flash green and you will hear three beeps. Enter Mastercode. Press Loc...
Install a fresh set of batteries and turn switch #3 to the ON position. Test each button on the keypad (one at a time) and listen for a beep on each button press. If beeping is not heard on all buttons, contact Technical Support for further troubleshooting. The Lock button does not lock the door.
If there are no codes in the lock, the lock button will not lock the door. This is indicated by the keypad flashing red three times with three beeps. Program at least one user code and test the Lock button again. The battery is too low to lock the door. This is indicated by the keypad flashing red three times with three beeps. Remove the batteries ...
If the lock has been unable to communicate with the system after multiple attempts, it will go into sleep mode. Lock and unlock the door with a key so that the lock status transmits to the system. If it still does not communicate, remove (exclude/unpair) the lock from your system. Then, pair (add/include) the lock with your system again. If the pro...
The batteries drain within one day. The lock must be replaced. Contact Technical Support. The batteries drain within one week.
See “Keypad error test” on page 7. The batteries drain within a few weeks. The smart home system’s user interface falsely reports a low battery. If you receive an alert from your smart home system indicating that the battery is low, confirm this is true at the lock. Turn on switch #1 so that the status LED flashes every six seconds. If the LEDs tur...
For best results, use new non-rechargeable Alkaline batteries only.
When the system is idling, it consumes minimum power (very close to battery shelf life.) With alkaline batteries, the lock should be operable after years of idle. I replaced my batteries less than a year ago and need to replace them again. Check your door alignment. If the deadbolt makes several unsuccessful attempts to lock or unlock the door, it ...
- 1MB
- 11
Answer. What do I do if I forget my mastercode on my Powerbolt 2? If you do not have the master or user code you may do a factory reset on the unit to program a new master code into the lock. The link provided will guide on how to factory reset the lock and program the lock. Click here. Read More. Answer.
For instructions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock.1. Keep door open. Press the Program button once.
Page 4 62812 / 01 Adding User Codes with the Mastercode Enabled The procedure for adding user codes is different when the Mastercode is enabled. For instuctions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock.
