Search results
May 5, 2020 · Hand sanitizer alone is unlikely to protect you from the virus. Here are a couple of other items of personal protection apparel that can help. Below is a huge roundup of free face mask sewing patterns as well as some surgical scrub caps. Face Mask Sewing Patterns Roundup. Surgical Scrub Caps for Frontline Healthcare Workers.
- So Sew Easy
Dec 3, 2020 · This project is perfect for a beginner sewer who needs basic sewing skills, is familiar with sewing patterns, and can sew straight seams. Large = 3” (7.5 cm) wide by 5” (12.5 cm) high. Small = 2.5” (6 cm) wide by 4” (10 cm) high. What you will need to make an Ava Sanitizer Pouch:-. Wonder clips /Pins.
Aug 31, 2020 · See the Easy Fabric Hand Sanitizer Holder video tutorial here. Prepare two sheets of 5″ x 5″ charm pack cotton fabrics. If you use scrap fabric, then cut two sheets of 5″ x 5″ squares. Cut the ribbon into two of 1″ each and use the lighter to seal the raw edge. Cut the elastic into 4″.
- (1)
- 1
Cut the lines on the inside of the template with a craft knife or fold it over and cut with scissors. Join two keyring loops together creating one ring at the bottom and one ring at the top. Leave one chain in the centre of both rings. Slide one end of the ring over the top hook loop.
- Step 1: Draw Your Hand Sanitizer Holder Pattern
- Step 2: Cut The Fabrics For The Diy Hand Sanitizer Holder
- Step 3: Make The Handle of The Hand Gel Pouch
- Step 4: Make The Front
- Step 6: Assembling The Back
- Step 7: Topstitching Front and Back
- Step 9: Adding Front Cover
- Step 10: Assembling The Hand Gel Holder
- Step 12: Turn Around and Press
- Step 14: Sew Buttonholes
Place the hand gel bottle on top of the paper. Hold the pencil straight (don’t tilt it!) and draw around the bottle. Don’t trace the bottle neck. Add 1/2 inch on each side of the bottle (add to the widest and highest points of the bottle) and create a rectangle pattern. You should also add 1/4 inch on each side of the bottle neck pattern to allow s...
You need to cut 6 pieces of fabric as follows: A – cover– 3/4 of the height of the template B – back– according to template C – front– according to template D – front lining– according to template E – back+cover lining– template + cover F – handle– 8 x 2.5″ Here’s a handy trick – to save some time place your lining fabric on a flat surface, fold yo...
Press one of the shortest sides 1/4″ inches in. Fold in half lengthwise and press again. Open up the handle and press each of the edges towards the middle crease you’ve just created. Press again, and fold the handle. Sew in place both the short and the long side. Leave the other short side unsewn.
Place front piece on top of the front lining, right (pretty) sides together. Sew along top and bottom edges using a 1/4″ seam allowance.
Place the back (B) on a flat surface, then place the unfinished edge of the handle (F) in the middle of the top edge, and then place the cover (A) on top. Right sides of the pieces should be facing each other. Sew along the top edge.
Turn the front piece around. Topstitch along the top, as close to the edge as possible. Open up the back piece, and fingerpress the seam allowance towards the backpiece. Topstitch in place to secure it.
Open up the back you’ve just assembled. Place the front assembly on top of the back lining. Align the unsewn edge to the middle seam.
Fold the side with the handle towards the cover. Pin everything in place with pins or clips. Now mark your stitching lines. Use your template to mark the opening for the hand sanitizer. Draw 1/2 inch markings along the sides near the bottom and join them with the markings for the opening. Mark the stitching line 1/4 inches in around the whole thing...
Turn the hand gel holder around through the opening. Push the corners out with a point turner or anything pointy (scissors or pen) you have on hand to give them a nice, sharp and professional look. Don’t skip pressing – I know that many of you might cringe – but believe me. Pressing is VERY important for the overall look of your makes.
Mark the position of the buttonholes on the cover and on the handle. Sew them up. Use your seamripper and a pin to open them.
Sew the seam down on either side. Fold the holder piece in half, lengthwise, and mark the center of the upper edge. Next, we finish the strap. 1) Take the strap piece, fold one of the short edges by 3/8- inch towards the wrong side and press. 2) Fold the two long edges towards the wrong side by 3/8- inch and press.
Here is a great scrap-busting project to DIY Fabric Hand Sanitizer Holder, a perfect gifts for all family members and all you care in your life! Click on over the links below and grab this cute and crazy quick sewing tutorial to make your own customized Hand Sanitizer Jacket makes a great gift for teachers, new moms, or the workplace grab-bag ...
