Search results
Method 1: Directly press and hold the reset button on the rear panel with a solid pin for approximately 8 to 10 seconds when the device is powered on. If you can see all the lights flashing, then go off and some lights go back on slowly, that means the device has been reset successfully. Method 2:
- How to hard reset TP-Link wireless access points, extenders to factory ...
How to hard reset TP-Link wireless access points, extenders...
- How to reset tp link extender - Home Network Community
Locate the pinhole on the side where the reset button is....
- How to hard reset TP-Link wireless access points, extenders to factory ...
The default network name (TP-Link Extender or TP-Link Extender_2.4GHz/5GHz) is provided for initial setup only. If you set up the extender via the Tether app or web management page, you can customize the network name as you like. If you set up the extender via the WPS button, its network name will be the same as your router or with EXT at the end.
- Relocate
- FAQ
- Safety Information
- Tp-Link Three Years Limited Product Warranty
To achieve better signal quality, plug in the extender halfway between your router and the Wi-Fi dead zone. Enjoy! Connect your device to the extender using the extended SSID and Wi-Fi password that you've set during the configuration. The default Wi-Fi password is the same as your host network. Entertainment Adapter If your extender has an Etherne...
Q1 Why can't I see the login page after entering http://tplinkrepeater.netin the browser? A1: Make sure your computer is connected to the extender either via the extended SSID or via an Ethernet cable (if the extender has an Ethernet port). A2: Make sure your computer is set to obtain an IP address automatically. A3: Use the IP address to access th...
Keep the device away from water, fire, humidity or hot environments.Do not attempt to disassemble, repair, or modify the device.Do not use the device where wireless devices are not allowed.The socket-outlet shall be installed near the equipment and shall be easilyaccessible.For TP-Link Branded Products Only. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE (OR BY COUN- TRY OR PROVINCE). TO THE EXTENT ALLOWED BY LOCAL LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WAR- RANTIES, REMEDIES AND CONDITIONS. TP-Link warrants the T...
- Before setup. Q1. Can the range extender work with a non-TP-Link router? Yes. The range extender works with almost any Wi-Fi router. But it may not be compatible with routers or gateways with firmware that has been altered, or is non-standard or outdated.
- Access the extender. Q3. How do I log into the range extender? Method 1: Via the Tether app. Connect your smartphone to the range extender’s Wi-Fi. Launch the app and tap your extender to log in.
- Extend the network. Q6. What should I do if the range extender can’t find my home network? Try rescanning networks, and double-check the list of scanned networks.
- Relocate the extender. Q8. How to confirm whether my range extender is in the best location? For better Wi-Fi coverage and signal strength, plug in the extender
Power on your extender, and run the Quick Setup to configure your extender. 3. Connect all of your devices to the extended network. 4. On your router, add all the Online Devices’ MAC addresses to your router’s MAC filter table. 5. Enable the router’s MAC filter, wireless access control, or ACL to complete the configuration. < Previous ...
it back in, then try again. Or use “Customize the Extender’s Wi-Fi Settings” on the back instead. If your router supports WPS, you can continue with the steps below to clone its current Wi-Fi settings to the extender. Tips: We recommend that you plug in the extender near your router for Wi-Fi cloning. Press the WPS button for 2 seconds. 1 ...
People also ask
How do I Reset my TP Link extender?
What is the default TP-Link extender network name?
How do I set up my TP-Link tether extender?
How do I connect a TP-Link extender to my computer?
