Search results
People also ask
How do I set up my TP-Link tether extender?
How do I Reset my wireless extender?
How do I connect a TP-Link extender to my computer?
How do I connect a wireless extender to my computer?
Method 1 is applicable for most of the models. For models which can be hard reset by using Method 2 please refer to appendix. Method 1: Directly press and hold the reset button on the rear panel with a solid pin for approximately 8 to 10 seconds when the device is powered on.
- How to Hard Reset Tp-Link Wireless Access Points, Extenders to Factory Defaults
How to hard reset TP-Link wireless access points, extenders...
- TP-Link United Kingdom
If you set up via the Tether app or web management page,...
- LOS
If you problem is not included, contact our Technical...
- How to Hard Reset Tp-Link Wireless Access Points, Extenders to Factory Defaults
If you set up via the Tether app or web management page, make sure you have entered the correct Wi-Fi password(s) for your home network router during setup. Make sure the extender is close to your router, preferably within 16 feet during setup, and away from large electrical appliances.
- Relocate
- FAQ
- Safety Information
- Tp-Link Three Years Limited Product Warranty
To achieve better signal quality, plug in the extender halfway between your router and the Wi-Fi dead zone. Enjoy! Connect your device to the extender using the extended SSID and Wi-Fi password that you've set during the configuration. The default Wi-Fi password is the same as your host network. Entertainment Adapter If your extender has an Etherne...
Q1 Why can't I see the login page after entering http://tplinkrepeater.netin the browser? A1: Make sure your computer is connected to the extender either via the extended SSID or via an Ethernet cable (if the extender has an Ethernet port). A2: Make sure your computer is set to obtain an IP address automatically. A3: Use the IP address to access th...
Keep the device away from water, fire, humidity or hot environments.Do not attempt to disassemble, repair, or modify the device.Do not use the device where wireless devices are not allowed.The socket-outlet shall be installed near the equipment and shall be easilyaccessible.For TP-Link Branded Products Only. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE (OR BY COUN- TRY OR PROVINCE). TO THE EXTENT ALLOWED BY LOCAL LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WAR- RANTIES, REMEDIES AND CONDITIONS. TP-Link warrants the T...
- Before setup. Q1. Can the range extender work with a non-TP-Link router? Yes. The range extender works with almost any Wi-Fi router. But it may not be compatible with routers or gateways with firmware that has been altered, or is non-standard or outdated.
- Access the extender. Q3. How do I log into the range extender? Method 1: Via the Tether app. Connect your smartphone to the range extender’s Wi-Fi. Launch the app and tap your extender to log in.
- Extend the network. Q6. What should I do if the range extender can’t find my home network? Try rescanning networks, and double-check the list of scanned networks.
- Relocate the extender. Q8. How to confirm whether my range extender is in the best location? For better Wi-Fi coverage and signal strength, plug in the extender
In Access Point mode, please connect your computer to the extender using an Ethernet cable and follow the steps below: 1. Visit http://tplinkrepeater.net, and log in with the password you set for the extender. 2. Go to Settings > Wireless > Wireless Settings to retrieve or reset your wireless password.
Jun 28, 2022 · 1) Go to Settings > Wireless > Extended Network. 2) Create a new SSID in Extended 2.4GHz SSID or click Copy Host SSID. The value is case sensitive. 3) Click Save. Note: If you change the wireless settings via a wireless device, you will be disconnected after the settings are applied. Please write down the new SSID for future use.
Wireless Security to set a new Wi-Fi password. 5 FAQ (Frequently Asked Questions) Q1. How do I reset my extender? A. With the extender powered on, use a pin to press and hold the Reset button until all LEDs go o˜. When the Power LED turns on and the Wi-Fi LED starts to blink rapidly, the reset process is complete. Q2.
