8.0/10 (190 reviews)
Instantly unlock your Samsung and use any sim card from any network. Enter your IMEI and get your Samsung Galaxy Unlock Code instantly
Search results
People also ask
How do I reprogramme my SmartCode 913?
Why is my SmartCode 913 lock button not working?
Where can I find a Kwikset SmartCode 913 troubleshooting guide?
Why is my Kwikset SmartCode 913 flashing red?
Feb 20, 2024 · One of the steps you can take to troubleshoot your Kwikset SmartCode 913 is to reset it. Also, if you've lost your code or want to remove all existing codes and add new codes, you'll ...more.
- 4 min
- 1011
- Smart TechVille
On my Smartcode Touchscreen, the batteries drain within one week. The Wireless Card LEDs are staying on. Remove the battery pack, press and hold the program button for 10 seconds. Replace the battery pack. If the Wireless Card LEDs continue to stay on, contact Technical Support. Read More
Perform a factory reset. A factory reset will delete all codes associated with the lock. 1. Remove battery pack. 2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. 3.
Kwikset Smartcode 913 Touchpad Electronic Deadbolt Programming and Troubleshooting Guide
- Kwikset Smartcode 913 Flashing Red Light
- Kwikset Smartcode 913 Solid Red Light.
- Kwikset Smartcode 913 Keypad Light Is Not working.
- Kwikset Smartcode 913 Wont Lock
- Kwikset Smartcode 913 Won’T unlock.
- Kwikset Smartcode 913 Keeps Locking.
- Kwikset Smartcode 913 Lock Button Not Working
- Kwikset Smartcode 913 Reset
- Kwikset Smartcode 913 User Manual
- Conclusion
If your Kwikset Smartcode 913 is flashing red, please check the following reasons and solutions why your Kwikset SmartCode 913 is flashing red light: 1. The keypad flashes red once with one beep:The door jammed while attempting to lock. Manually re-lock the door. If needed, reposition strike. 2. The keypad flashes red three times with three beeps. ...
The lock interior is not mounted perpendicular to the ground. Remount lock interior assembly as illustrated in the Kwikset deadbolt InstallationGuide.The hole in the door is misaligned. Disassemble the lock and reinstall it without the adapter ring on the exterior side of the door.The battery level is too low. The keypad flashes red three times with three beeps, indicating the low battery. Use a fresh set of batteries and perform the door-handing process again.The latch and strike are misaligned, causing the latch to bind. If you have not done so, perform the door-handing process while the door is open. If it is successful only when the door is open, the...If your keypad light doesn’t work, it could be because of one of the following reasons: 1. Check the battery. Please make sure they are fresh and inserted correctly. The lock will not work with dead batteries or improperly inserted batteries. 2. Make sure your keypad is not damaged. Press each key on the keypad (one at a time) and listen for a beep...
If your door lock’s deadbolt isn’t locking, try these troubleshooting steps: 1. Check the battery. Remove the battery to see if it’s drained. If so, replace 4 AA batteries with new ones and try again (it’s important to use the same type of batteries). 2. Double-check that you’ve installed your new batteries correctly. Ensure they’re installed in a ...
If your door doesn’t unlock, check the following: 1. Make sure the door latch is fully engaged. That could be why your SmartCode 913 won’t unlock if it’s not. 2. Check the hinges on your door frame and ensure they’re in good shape. If one is loose or broken, it could prevent proper engagement of the SmartCode 913 during unlocking. 3. Check that the...
If you find that your SmartCode 913 keeps locking and unlocking, there are several possible causes: 1. The extended deadbolt lock was hitting the back of the drilled frame,so it did not fully extend when it locked. I thought it was not locked and would try every 30 seconds again. 2. The internal assembly may be screwed down too tight to allow enoug...
Suppose your SmartCode 913 lock button is not working. The following are the possible reasons and solutions: 1. No user codes are programmed:The lock button will not lock the door if no codes are in the lock. Program at least one user code and test the Lock button again. 2. The door-handing process was not executed:Perform the door-handing process,...
To factory reset Kwikset 913: 1. Remove the battery pack. 2. Press and HOLD the Program button while reinserting the battery pack. Hold the button for 30 seconds until the lock beeps and the Status LED flashes red. 3. Press the Program button once more. The lock has been reset when the LED flashes green, and you hear one beep. 4. Perform the door-h...
For more information about Kwikset SmartCode 913 programming and troubleshooting, you can download and check the following Kwikset SmartCode 913 user manuals: 1. Kwikset SmartCode 913 User Manual PDF 2. Kwikset SmartCode 913 troubleshooting Manual PDF
We hope this post has helped you with programming and troubleshooting your Kwikset SmartCode 913. If these tips don’t work, please get in touch with ShineACS Locks, and we’ll try to help.
Make sure the Mastercode has not already been programmed. Attempt the procedure again, making sure to enter the same new Mastercode in step 2 and 4. Make sure switch #3 is on, and press the Program button once. If you hear three beeps and see the keypad flash green, the Mastercode is enabled.
Feb 1, 2024 · How can I reset my lock code on the SmartCode 913? To reset your lock code on the SmartCode 913, follow these steps: Keep the door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds). Enter a new Mastercode. Make sure to avoid timeouts by completing each step within 5 seconds.
