Search results
- For instuctions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. Keep door open. Press the Program button once. The Checkmark will flash five times and you will hear five beeps.
www.manualslib.com/manual/2892370/Kwikset-Smartcode-916.html
People also ask
How do I add a user code if the mastercode is disabled?
How do I add user codes?
How do I enable a mastercode?
How do I disable a mastercode?
How do I know if my mastercode is disabled?
Why do I need a mastercode?
For instructions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. 1. Keep door open. Press the Program button once. The Checkmark will flash five times and you will hear five beeps. 2. Press Checkmark symbol once. 3. Enter Mastercode.
- F Disabling and Deleting the Mastercode
- The battery level is too low.
- The hole in the door is misaligned.
- The battery level is too low.
- The keypad is unresponsive.
- Troubleshooting: Smart Home Systems (cont.)
- The network configuration changed.
- The lock is in sleep mode.
- What type of batteries do you recommend?
- I am planning to be away for several months. Will my lock operate when I get back?
Make sure the audio setting on the lock is turned on / not muted. Keep door open. Press and HOLD the Program button until the lock button flashes green (about 5 seconds). Press Lock button once. Enter Mastercode. Press Lock button once. Re-enter Mastercode. Press Lock button once. If disabling is successful, the lock button will flash green once wi...
Remove the battery pack, and replace the batteries with a new set of good quality disposable alkaline batteries. Reinstall the battery pack. Press the lock button on the exterior keypad or execute a lock command inside your smart home app to lock the door.
Disassemble the lock, and reinstall it without the adapter ring on the exterior side of the door.
This is indicated by the lock button flashing red three times with three beeps. Use a fresh set of batteries, and perform the door handing process again. C4 The latch and strike are misaligned, causing the latch to bind. If you have not already done so, perform the door handing process while the door is open. If it is successful only when the door ...
Use a fresh set of batteries and perform the door handing process. If the latch does not extend or retract, and the lock does not beep, press each individual key on the keypad (one at a time) and listen for beeping sound. If no beeping is heard, this is a keypad error. Contact Technical Support for further troubleshooting.
B I can see the lock in my controller, but I can’t control it from the controller. The system needs a repeater or router to reach the lock. Adding repeaters to your system may help communication between your lock and the controller, especially if they are far away from each other.
If any repeaters or routers in the system were moved since adding the lock to the system, perform the “rediscover” process in your system’s user interface.
If the lock has been unable to communicate with the system after multiple attempts, it will go into sleep mode. Lock and unlock the door with a key so that the lock status transmits to the system. If it still does not communicate, remove (exclude/unpair) the lock from your system. Then, pair (add/include) the lock with your system again. If the pro...
For best results, use new non-rechargeable Alkaline batteries only.
When the system is idling, it consumes minimum power (very close to battery shelf life.) With alkaline batteries, the lock should be operable after years of idle. I replaced my batteries less than a year ago and need to replace them again. Check your door alignment. If the deadbolt makes several unsuccessful attempts to lock or unlock the door, it ...
- 4MB
- 18
For instructions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock.1. Keep door open. Press the Program button once.
Adding User Codes with the Mastercode Enabled. The procedure for adding user codes is different when the Mastercode is enabled. For instructions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. Keep door open.
For instuctions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with your lock. Keep door open. Press the Program button once. The keypad will flash green and you will hear three beeps. Enter Mastercode. Press Lock button once.
The procedure for adding user codes is different when the Mastercode is enabled. For instuctions on how to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with
Apr 30, 2024 · Model. To add new user codes to your Powerbolt 2, ensure the lock is unlocked and the door is open. Enter your master code (default is 0-0-0-0 for new installations), then press the lock button to hear a single beep. Press 1, then the lock button again, followed by entering a new 4-10 digit user code. Lastly, press the lock button once more.
